The robot needs to be maintained regularly. Follow these steps to remove debris from the robot:
1.Turn off the power switch. Remove and empty the dustbin.
2.Clean the primary and high-performance filters.
3.Clean the main brush.
4.Remove and clean the side brushes.5. Remove and clean the main brush.

1.Please check that the app version matches the region version
（1）Turn the machine over, remove the dust box, and check the MAC ID number on the label
（2）North America corresponds to US version：US Region or ALIGW Region
2.Check if the machine is bound by someone else's mobile app
（1）You can log in to the original account to unbind. (Refer to the instructions for use)
（2）Re-networking can force unbundling
（3）Contact the after-sales service, and provide the serial number and registered email address at the same time
3.The machine is not connected to the network
（1）Check whether the distribution network model you selected in the app is consistent with the actual model.
（2）WIFI password must be entered correctly
（3）Cannot use 5G WIFI signal
（4）Check if the router is blacklisted
（5）It is not recommended to use corporate WIFI or public WIFI
4. The phone can't find the machine's hotspot Robot_XXXXX
（1）Check the hotspot name of the machine Robot_XXXX or adh_XXX
（2）Please confirm that your distribution network operation steps are correct. After booting, you need to wait 30 seconds, and then press and hold the button for more than 5 seconds to configure the network.(It is not recommended to distribute the network in or around the charging base)
（3）Try again after shutdown and restart

1.Clean the charging pins on the robot and the charging dock if they are dirty. Try to recharge the robot again.
2.Press the Home button on the remote to let the robot dock itself instead of placing the robot on the dock yourself.

1. The robot will automatically clean the areas that it has missed. Do not move it or block its cleaning route.
2. Because every home setting is different, spatial analysis discrepancy may happen. If the robot hasn’t covered some areas, put it in another spot manually and restart the cleaning cycle.
3. Before using the robot, clear excessive objects on the floor that may block its cleaning path (e.g. cables, slippers, upright fan). The robot cannot clean narrow spaces which are smaller than itself. Rearrange the furniture and settings for better cleaning results.

1. The robot’s battery is low and has entered into search mode for the charging base. The robot's side brushes and wheels will move slower in this mode.
2. Side brushes are jammed by debris. Remove and clean them.

1. Check if the bumper is out all the way. Loosen the screws along the front bumper and tap to restore it to the original position. If nesessary, remove the front bumper, clean and reinstall (make sure not to make screws too tight).
2. Clean the cliff sensors if they are dusty or covered by debris. If problem persists, contact our customer care.

The charging station is placed against the wall, each side is 0.5 meters, and there is no obstacle in the front 1.5 meters. Away from signal interference, such as router TVs,mirrors, windows, etc.

The wheels maybe blocked with hair, clean it with tools. (if there is still the phenomenon, please contact our after-sales service)

The machine nose wheel is blocked with objects. Remove the nose wheel and cleaning.

Clean the robot charging pins and the Charging contact shrapnel on the Auto-empty station with a dry cloth. Check whether the indicator light on the Auto-empty station is always on, and check whether the dust box is properly installed in place

The capacity of the dust bag is 2.5L. If it is cleaned every two days, the dust bag should be replaced every 60 days or so.If there are a lot of garbage that needs to be cleaned, you can observe and calculate the specific time according to your own environment

Please check whether the indicator light on the front of the Auto-empty station is always white. If not, please check whether the power cord is plugged in and whether the internal dust bag is installed correctly. Please check in the APP whether the cleaning area exceeds 3 square meters, please check the dust collection settings, and check whether the do not disturb time is set,because of the Do Not Disturb time, the Auto-empty station will not automatically collect garbage

After the APP is set successfully, does the machine have a voice response setting successfully? Does the app have set do-not-disturb time? Because the appointment will not work during the do not disturb time

The dustbin filter is maybe block. Remove the dustbin and check if it is block. (High-efficiency filter has a service life about six months)